Electrical properties and technical data Property Description / value Operating voltage 12 … 57.6 V DC Rated current @40°C CPB3-...: 3 Arms CPB6-...: 6 Arms (for temperature derating, see Overtemperature protection) CPB15-...: 15 Arms (@25°C) 10 Arms (@40°C) Peak current @40°C CPB3-1-...: 3 Arms CPB3-2-...: 9 Arms (for max. 5 seconds) CPB6-1-...: 6 Arms CPB6-2-...: 18 Arms (for max. 5 seconds) CPB15-...: 45 Arms (for max. 5 seconds) Commutation CPB3-..., CPB6-...: Stepper motor open-loop, stepper motor closed-loop with encoder, BLDC sine commutated via Hall sensor, BLDC sine commutated via encoderCPB15-…: BLDC sine commutated via Hall sensor, BLDC sine commutated via encoder Note: External wiring is required for encoder and Hall sensor! Operating modes Profile Position Mode, Profile Velocity Mode, Profile Torque Mode, Velocity Mode, Homing Mode, Interpolated Position Mode, Cyclic Sync Position Mode, Cyclic Sync Velocity Mode, Cyclic Synchronous Torque Mode, Clock-Direction Mode Set value setting / programming Clock-direction, analog, NanoJ program Interfaces USB, CANopenNote: External wiring is required for USB and CANopen! Encoder/Hall 1x SSI encoder, 1x Hall sensor, 1x incremental encoder (second SSI encoder can be configured instead) Note: External wiring is required for encoder and Hall sensor! I/O 12x general I/Os (one of which can be used as output for external brake), 2x analog inputs, 1x output for external ballast circuit Overtemperature Protection circuit at temperature > 80°C Charging capacitor For each ampere of rated current on the motor, Nanotec recommends a capacitance of approx. 1000 µF.
Electrical properties and technical data Property Description / value Operating voltage 12 … 57.6 V DC Rated current @40°C CPB3-...: 3 Arms CPB6-...: 6 Arms (for temperature derating, see Overtemperature protection) CPB15-...: 15 Arms (@25°C) 10 Arms (@40°C) Peak current @40°C CPB3-1-...: 3 Arms CPB3-2-...: 9 Arms (for max. 5 seconds) CPB6-1-...: 6 Arms CPB6-2-...: 18 Arms (for max. 5 seconds) CPB15-...: 45 Arms (for max. 5 seconds) Commutation CPB3-..., CPB6-...: Stepper motor open-loop, stepper motor closed-loop with encoder, BLDC sine commutated via Hall sensor, BLDC sine commutated via encoderCPB15-…: BLDC sine commutated via Hall sensor, BLDC sine commutated via encoder Note: External wiring is required for encoder and Hall sensor! Operating modes Profile Position Mode, Profile Velocity Mode, Profile Torque Mode, Velocity Mode, Homing Mode, Interpolated Position Mode, Cyclic Sync Position Mode, Cyclic Sync Velocity Mode, Cyclic Synchronous Torque Mode, Clock-Direction Mode Set value setting / programming Clock-direction, analog, NanoJ program Interfaces USB, CANopenNote: External wiring is required for USB and CANopen! Encoder/Hall 1x SSI encoder, 1x Hall sensor, 1x incremental encoder (second SSI encoder can be configured instead) Note: External wiring is required for encoder and Hall sensor! I/O 12x general I/Os (one of which can be used as output for external brake), 2x analog inputs, 1x output for external ballast circuit Overtemperature Protection circuit at temperature > 80°C Charging capacitor For each ampere of rated current on the motor, Nanotec recommends a capacitance of approx. 1000 µF.
